[RESUELTO] Elastix 2.3 con E1 de Telmex

[Duquelin]

muchas gracias por tu ayuda! te comento que el E1 fraccionado que tego ( 10 lineas) si funciona bien ya que esta puesto en otro equipo al cual queremos muchas remplazar.
hay va la info
[root@conmutador ~]# asterisk -r
Asterisk 1.8.11.0, Copyright (C) 1999 - 2012 Digium, Inc. and others.
Created by Mark Spencer <markster@digium.com>
Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for details.
This is free software, with components licensed under the GNU General Public
License version 2 and other licenses; you are welcome to redistribute it under
certain conditions. Type 'core show license' for details.
================================================== =======================
Connected to Asterisk 1.8.11.0 currently running on conmutador (pid = 3442)
Verbosity is at least 3
conmutador*CLI> mfcr2 show channels
Chan Variant Max ANI Max DNIS ANI First Immediate Accept Tx CAS Rx CAS
1 MX 10 4 No No IDLE BLOCK
2 MX 10 4 No No IDLE BLOCK
3 MX 10 4 No No IDLE BLOCK
4 MX 10 4 No No IDLE BLOCK
5 MX 10 4 No No IDLE BLOCK
6 MX 10 4 No No IDLE BLOCK
7 MX 10 4 No No IDLE BLOCK
8 MX 10 4 No No IDLE BLOCK
9 MX 10 4 No No IDLE BLOCK
10 MX 10 4 No No IDLE BLOCK
11 MX 10 4 No No IDLE BLOCK
12 MX 10 4 No No IDLE BLOCK
13 MX 10 4 No No IDLE BLOCK
14 MX 10 4 No No IDLE BLOCK
15 MX 10 4 No No IDLE BLOCK
17 MX 10 4 No No IDLE BLOCK
18 MX 10 4 No No IDLE BLOCK
19 MX 10 4 No No IDLE BLOCK
20 MX 10 4 No No IDLE BLOCK
21 MX 10 4 No No IDLE BLOCK
22 MX 10 4 No No IDLE BLOCK
23 MX 10 4 No No IDLE BLOCK
24 MX 10 4 No No IDLE BLOCK
25 MX 10 4 No No IDLE BLOCK
26 MX 10 4 No No IDLE BLOCK
27 MX 10 4 No No IDLE BLOCK
28 MX 10 4 No No IDLE BLOCK
29 MX 10 4 No No IDLE BLOCK
30 MX 10 4 No No IDLE BLOCK
31 MX 10 4 No No IDLE BLOCK

[Duquelin]

[root@conmutador ~]# wanpipemon -i w1g1 -c Ta

***** w1g1: E1 Rx Alarms (Framer) *****

ALOS: OFF | LOS: OFF
RED: ON | AIS: OFF
LOF: ON | RAI: OFF

***** w1g1: E1 Rx Alarms (LIU) *****

Short Circuit: OFF
Open Circuit: OFF
Loss of Signal: OFF

***** w1g1: E1 Tx Alarms *****

AIS: OFF | YEL: ON


***** w1g1: E1 Performance Monitoring Counters *****

Line Code Violation : 863
Far End Block Errors : 0
CRC4 Errors : 0
FAS Errors : 0

[Marco Zink]

Se ve que hay alarmas en la tarjeta, puedes poner el wanpipe1.conf?

[Duquelin]

con gusto!

#================================================
# WANPIPE1 Configuration File
#================================================
#
# Date: Wed Dec 6 20:29:03 UTC 2006
#
# Note: This file was generated automatically
# by /usr/local/sbin/setup-sangoma program.
#
# If you want to edit this file, it is
# recommended that you use wancfg program
# to do so.
#================================================
# Sangoma Technologies Inc.
#================================================

[devices]
wanpipe1 = WAN_AFT_TE1, Comment

[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment

[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 1
PCIBUS = 3
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = CRC4
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0

TE_HIGHIMPEDANCE = NO
TE_SIG_MODE = CCS
TE_RX_SLEVEL = 120
HW_RJ45_PORT_MAP = DEFAULT
LBO = 120OH
FE_TXTRISTATE = NO
MTU = 1500
UDPPORT = 9000
TTL = 255
IGNORE_FRONT_END = NO
TDMV_SPAN = 1
TDMV_DCHAN = 16
TE_AIS_MAINTENANCE = NO #NO: defualt YES: Start port in AIS Blue Alarm and keep line down
#wanpipemon -i w1g1 -c Ttx_ais_off to disable AIS maintenance mode
#wanpipemon -i w1g1 -c Ttx_ais_on to enable AIS maintenance mode
TDMV_HW_DTMF = NO # YES: receive dtmf events from hardware
TDMV_HW_FAX_DETECT = NO # YES: receive fax 1100hz events from hardware
HWEC_OPERATION_MODE = OCT_NORMAL # OCT_NORMAL: echo cancelation enabled with nlp (default)
# OCT_SPEECH: improves software tone detection by disabling NLP (echo possible)
# OCT_NO_ECHO:disables echo cancelation but allows VQE/tone functions.
HWEC_DTMF_REMOVAL = NO # NO: default YES: remove dtmf out of incoming media (must have hwdtmf enabled)
HWEC_NOISE_REDUCTION = NO # NO: default YES: reduces noise on the line - could break fax
HWEC_ACUSTIC_ECHO = NO # NO: default YES: enables acustic echo cancelation
HWEC_NLP_DISABLE = NO # NO: default YES: guarantees software tone detection (possible echo)
HWEC_TX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio level to be maintained (-20 default)
HWEC_RX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio level to be maintained (-20 default)
HWEC_TX_GAIN = 0 # 0: disable -24-24: db values to be applied to tx signal
HWEC_RX_GAIN = 0 # 0: disable -24-24: db values to be applied to tx signal

[w1g1]
ACTIVE_CH = ALL
TDMV_HWEC = NO
MTU = 8

[Marco Zink]

Cambia los valores a:

FE_FRAME = NCRC4
TE_SIG_MODE = CAS

si editaste el /dahdi/system.conf para cas?

[Duquelin]

Maestro ...Al Maestro....
ahora si les debo unas Frias! ya JALO!
espero que este Post sirva como guia a cualquier otra persona que caiga en mis mismos errores!

mil gracias!

[Duquelin]

Muchas Gracias !

[Christian Cabrera]

Para eso estamos ;-)

Voy a cambiar el tema a resuelto para que sepan que este post sirve como base para quien sufra del mismo problema.