Tengo un problema durante la instalacion de una tarjeta sangoma A104DE.
La instalo completamente, despues de DAHDI.
Compilo primero los driver de Sangoma.
Y luego lo instalo de ./Setup dahdi --dahdi-chink=40

Despues de instalado me aparece el mensaje:
Al reiniciar wanrouter aparece:

Starting up device: wanpipe1

    wanconfig: WAN device wanpipe1 driver load failed !!
             : ioctl(wanpipe1,ROUTER_SETUP) failed:
             :      22 - Invalid argument


    Wanpipe driver did not load properly
    Please check /var/log/wanrouter and
    /var/log/messages for errors

Configuring interfaces: w1g1 w1g1: unknown interface: No such device

done.

En Wanrouter aparece:

Starting up device: wanpipe1
WAN Router Configurator(c) 1995-2003 Sangoma Technologies Inc.

Parsing configuration file /etc/wanpipe/wanpipe1.conf ...
Reading section ...
Reading section ...
Reading section ...
w1g1 to used by TDM_VOICE
Reading section ...
Configuring device wanpipe1 (no description)
Setting CARD_TYPE to AFT
Setting S514CPU to A
Setting COMMPORT to PRI
Setting AUTO_PCISLOT to NO
Setting PCISLOT to 4
Setting PCIBUS to 8
Setting FE_MEDIA to E1
Setting FE_LCODE to HDB3
Setting FE_FRAME to NCRC4
Setting FE_LINE to 1
Setting TE_CLOCK to NORMAL
Setting TE_REF_CLOCK to 0
Setting TE_SIG_MODE to CCS
Setting TE_HIGHIMPEDANCE to NO
Setting TE_RX_SLEVEL to 430
Setting HW_RJ45_PORT_MAP to DEFAULT
Setting LBO to 120OH
Setting FE_TXTRISTATE to NO
Setting MTU to 1500
Setting UDPPORT to 9000
Setting TTL to 255 * Setting TE_AIS_MAINTENANCE to NO
Setting TDMV_HW_DTMF to YES
Setting TDMV_HW_FAX_DETECT to NO
Setting HWEC_OPERATION_MODE to OCT_NORMAL
Setting HWEC_DTMF_REMOVAL to NO
Setting HWEC_NOISE_REDUCTION to NO
Setting HWEC_ACUSTIC_ECHO to NO
Setting HWEC_NLP_DISABLE to NO
Setting HWEC_TX_AUTO_GAIN to 0
Setting HWEC_RX_AUTO_GAIN to 0
Setting HWEC_TX_GAIN to 0
Setting HWEC_RX_GAIN to 0
Setting IGNORE_FRONT_END to NO
Setting TDMV_SPAN to 1
Setting TDMV_DCHAN to 16

En message aparece:

2015-08-25T12:17:58.795426-05:00 PBX kernel: [ 6077.005165] WANPIPE(tm) Hardware Support Module 7.0.14.3.0 (c) 1994-2013 Sangoma Technologies Inc
2015-08-25T12:17:58.795448-05:00 PBX kernel: [ 6077.005697] usbcore: registered new interface driver sdlausb
2015-08-25T12:17:58.799393-05:00 PBX kernel: [ 6077.010020] WANPIPE(tm) Interface Support Module 7.0.14.3.0 (c) 1994-2013 Sangoma Technologies Inc
2015-08-25T12:17:58.815433-05:00 PBX kernel: [ 6077.027491] WANPIPE(tm) Multi-Protocol WAN Driver Module 7.0.14.3.0 (c) 1994-2013 Sangoma Technologies Inc
2015-08-25T12:17:58.815470-05:00 PBX kernel: [ 6077.027506] wanpipe: Probing for WANPIPE hardware.
2015-08-25T12:17:58.819419-05:00 PBX kernel: [ 6077.031271] wanpipe: AFT-A104-SH PCIe T1/E1 card found (HDLC (DS) rev.45), cpu(s) 1, line(s) 4, bus #8, slot #4, irq #26
2015-08-25T12:17:58.823384-05:00 PBX kernel: [ 6077.035160] wanpipe: AFT-A104-SH PCIe T1/E1 card found (HDLC (DS) rev.45), cpu(s) 1, line(s) 4, bus #11, slot #4, irq #16
2015-08-25T12:17:58.823398-05:00 PBX kernel: [ 6077.035196] wanpipe: Allocating maximum 8 devices: wanpipe1 - wanpipe8.
2015-08-25T12:17:58.823400-05:00 PBX kernel: [ 6077.035669] WANPIPE: TDM Codecs Initialized
2015-08-25T12:17:58.831404-05:00 PBX kernel: [ 6077.044417] WANPIPE(tm) Socket API Module 7.0.14.3.0 (c) 1994-2013 Sangoma Technologies Inc
2015-08-25T12:17:58.831417-05:00 PBX kernel: [ 6077.044422] NET: Registered protocol family 25
2015-08-25T12:17:58.847372-05:00 PBX kernel: [ 6077.058981] WANPIPE(tm) WANEC Layer 7.0.14.3.0 (c) 1995-2006 Sangoma Technologies Inc.
2015-08-25T12:17:58.847394-05:00 PBX kernel: [ 6077.058987] wanec_create_dev: Registering Wanpipe ECDEV Device!
2015-08-25T12:17:58.855433-05:00 PBX kernel: [ 6077.067800] wanpipe1: Starting WAN Setup
2015-08-25T12:17:58.855445-05:00 PBX kernel: [ 6077.067804]
2015-08-25T12:17:58.855433-05:00 PBX kernel: [ 6077.067800] wanpipe1: Starting WAN Setup
2015-08-25T12:17:58.855445-05:00 PBX kernel: [ 6077.067804]
2015-08-25T12:17:58.855447-05:00 PBX kernel: [ 6077.067806] Processing WAN device wanpipe1...
2015-08-25T12:17:58.855448-05:00 PBX kernel: [ 6077.067811] wanpipe1: Locating: A101/1D/2/2D/4/4D/8/8D/16/16D card, CPU A, PciBus=8, PciSlot=4
2015-08-25T12:17:58.855449-05:00 PBX kernel: [ 6077.067818] wanpipe1: Found: A101/1D/2/2D/4/4D/8/8D/16/16D card, CPU A, PciBus=8, PciSlot=4, Port=0
2015-08-25T12:17:58.855450-05:00 PBX kernel: [ 6077.067859] wanpipe1: AFT PCI memory at 0xF7EE0000
2015-08-25T12:17:58.855451-05:00 PBX kernel: [ 6077.067861] wanpipe1: IRQ 26 allocated to the AFT PCI card
2015-08-25T12:17:58.855452-05:00 PBX kernel: [ 6077.067886] wanpipe1: Starting AFT 2/4/8 Hardware Init.
2015-08-25T12:17:58.855452-05:00 PBX kernel: [ 6077.067894] wanpipe1: Enabling front end link monitor
2015-08-25T12:17:58.855453-05:00 PBX kernel: [ 6077.067897] wanpipe1: Global Chip Configuration: used=1 used_type=1
2015-08-25T12:17:58.859423-05:00 PBX kernel: [ 6077.071248] wanpipe1: Global E1 Front End configuration
2015-08-25T12:17:58.859434-05:00 PBX kernel: [ 6077.072314] wanpipe1: AFT Data Mux Bit Map: 0x01234567
2015-08-25T12:17:58.859435-05:00 PBX kernel: [ 6077.072351] wanpipe1: Configuring DS DS26524 E1 FE
2015-08-25T12:17:58.859436-05:00 PBX kernel: [ 6077.072353] wanpipe1: Port 1,HDB3,non-CRC4,120OH
2015-08-25T12:17:58.859438-05:00 PBX kernel: [ 6077.072356] wanpipe1: Clk Normal:0, Channels: FFFFFFFF
2015-08-25T12:17:58.859439-05:00 PBX kernel: [ 6077.072357] wanpipe1: AIS on LOS: Off (default)
2015-08-25T12:17:58.859440-05:00 PBX kernel: [ 6077.072359] wanpipe1: Sig Mode CCS
2015-08-25T12:17:58.867398-05:00 PBX kernel: [ 6077.078805] wanpipe1: Rx Sensitivity Gain 43dB (default).
2015-08-25T12:17:58.867409-05:00 PBX kernel: [ 6077.078825] wanpipe1: Configurig DS8/4/2/1 for E1 LRISMR=0x33
2015-08-25T12:17:58.867410-05:00 PBX kernel: [ 6077.079527] wanpipe1: Front end successful
2015-08-25T12:17:58.867411-05:00 PBX kernel: [ 6077.079537] wanpipe1: Configuring FE Line=1 Clock Source: Line=1 Normal
2015-08-25T12:17:58.867412-05:00 PBX kernel: [ 6077.079767] wanpipe1: Front End Interface Ready 0x40100000
2015-08-25T12:17:58.867413-05:00 PBX kernel: [ 6077.079782] wanpipe1: Register EC interface wanec1 (usage 1, max ec chans 128)!
2015-08-25T12:17:58.867413-05:00 PBX kernel: [ 6077.079799] wanpipe1: Configuring Device :wanpipe1 FrmVr=45
2015-08-25T12:17:58.867414-05:00 PBX kernel: [ 6077.079800] wanpipe1: Global MTU = 1500
2015-08-25T12:17:58.867415-05:00 PBX kernel: [ 6077.079802] wanpipe1: Global MRU = 1500
2015-08-25T12:17:58.867416-05:00 PBX kernel: [ 6077.079803] wanpipe1: Data Mux Map = 0x01234567
2015-08-25T12:17:58.867417-05:00 PBX kernel: [ 6077.079805] wanpipe1: Rx CRC Bytes = 0
2015-08-25T12:17:58.867418-05:00 PBX kernel: [ 6077.079806] wanpipe1: RBS Signalling = Off
2015-08-25T12:17:58.867419-05:00 PBX kernel: [ 6077.079808] wanpipe1: FE Sync = Enabled
2015-08-25T12:17:58.867419-05:00 PBX kernel: [ 6077.079809] wanpipe1: Global TDM Int = Enabled
2015-08-25T12:17:58.867420-05:00 PBX kernel: [ 6077.079811] wanpipe1: Global TDM Ring= HW Ring
2015-08-25T12:17:58.867421-05:00 PBX kernel: [ 6077.079812] wanpipe1: Global SPAN IRQ= RX/TX
2015-08-25T12:17:58.867422-05:00 PBX kernel: [ 6077.079814] wanpipe1: TDM HW TONE = Enabled
2015-08-25T12:17:58.867423-05:00 PBX kernel: [ 6077.079818] wanpipe1: Fifo Trigger = rx:50 tx:50 (events per sec)
2015-08-25T12:17:58.867424-05:00 PBX kernel: [ 6077.079820] wanpipe1: TDMV Span = 1 : Enabled
2015-08-25T12:17:58.867425-05:00 PBX kernel: [ 6077.079821] wanpipe1: RTP TAP = Disabled
2015-08-25T12:17:58.867426-05:00 PBX kernel: [ 6077.079895]
2015-08-25T12:17:58.867427-05:00 PBX kernel: [ 6077.079898] wanpipe1: Error: TDM VOICE prot not compiled
2015-08-25T12:17:58.867427-05:00 PBX kernel: [ 6077.079899] wanpipe1: during installation process!

¿Que me falta o que proceso estoy haciendo mal?

Gracias
Saludos